Chainsaw question: I'm missing something...?

[Limitool]

Is it a 3/8th pitch or .325. does it have a set screw for the oiler some of the new epa Stihl saws you cant adjust the oiler. It was always standard one tank of fuel ,one tank of oil Not with the new ones.

I will say when I was building bridges for the rail road we cut a ton of creosote ties and supports. We had a large wheel of chain to replace after a few sharpenings. Creosote made the blades and bar run very hot. Old ties should not be a problem though. Good practice always flip your bar over when replacing a chain for even bar wear. I love chain saws !

Tnmountains: Can't answer on the pitch. No set screw for oiler. ! tank of fuel / 1 of oil. AND this saw is running HOT both blade and bar. But these are old ties though...? But thanks for advise of flipping bar over for wear.... That makes a LOT of sense.... Thanks...!

 

Amazon Forum Fav 👍

Diving for Pleasure and Treasure - Grab it through Amazon!

[pepperj]

Problem solved😁

 

[robertk]

Problem solved😁
View attachment 2176398

I was waiting to see him pick up a railroad tie...

 

[Gare]

I love the way the guy tied the chain saw up and cut the wood

 

[cyzak]

I have a Stihl chainsaw w/18" bar. Fairly new and not used much. I've had a few hundred railroad ties stacked up for lining the driveway since last year. Well started to move them and had angles to cut at curves. After 2 cuts it was running hot and puked the chain. I changed out chain and made 3 cuts and again same thing. I took bar & chain off and cleaned up everything to make sure bar oil was in the oiler. I fired it up and yep.... oil pouring on out. Put a 3rd new chain on and cut 9 ties and same thing happened AGAIN...!

So is something wrong with the chainsaw or maybe it doesn't like cutting the railroad ties possibly. Why I wouldn't know but is it possible maybe? I am NOT hitting any metal nor seen any sparks at all. I stay a long ways from the metal end plates.

Any ideas anybody....

Is it possible the chain is on backwards I have done this myself with the same results.

 

[Tnmountains]

There is bar oil for summer and oil for winter. I always shoot a shot of wd -40 in my one saw with auto oiler to thin it down so it throws out a ton of oil, Lol. Be careful out there!

 

[Back-of-the-boat]

Is it possible the chain is on backwards I have done this myself with the same results.

Been there done that, when I was a kid.

 

[Limitool]

Is it possible the chain is on backwards I have done this myself with the same results.

Nope and certainly not 3 times.

 

[releventchair]

Check your chains rear sprockets rim it rides on. They wear for a reason and could be considered sacrificial in a good way of sorts. Your sprocket should indicate it wants replaced from the sounds of it. I mean from what you described of your chain wandering. You checked how the chain rode in/on it when you hanged chains repeatedly right? It's just as easy to measure against a new ones attributes/dimensions.
(Not your actual rim shown in sample picture. A side view would show where chain rides.)

https://www.jackssmallengines.com/equipment/stihl/chainsaw/sprockets

Bump up your oil in your oil mix. That should keep your fuel from boiling. And as mentioned run that dog. Don't lug the r.p.m.s. Worst case if you add too much oil you'll foul a plug while fogging mosquitos. (Tilt saw and smoke out some chiggers too while you're at it.)

Now , a real man would just use a hand saw.
(I'd have returned the ties design arrangement back where they were after smoking my first chain.).

 

[unclemac]

Now , a real man would just use a hand saw.

I put my great grandpa's cross-cut up on my wall by the wood stove.... my dad came over and saw it... he said..."I spent a lot of time on the other end of that saw..."

 

[releventchair]

Now , a real man would just use a hand saw.

View attachment 2176466
I put my great grandpa's cross-cut up on my wall by the wood stove.... my dad came over and saw it... he said..."I spent a lot of time on the other end of that saw..."

I didn't get in any fistfight over Dads buck saw when we settled his estate.
Why my arms were not bigger than my legs one woodcutting Autumn escapes me.
Perhaps it was it only being a couple days of sawing. Well a couple hours of sawing anyways.
Kept me away from his chainsaws though I guess.
Now I have my own saws leaking oil . Why do I always end up with non-house broken ones....
.

.

 

[unclemac]

I have his buck-saw up on the wall too!

 

[ncsuwolf]

Been there done that, when I was a kid.

Buddy of mine bought an almost new ms027 about 30 years ago for hardly nothing. Guy he bought it from claimed it wouldn’t cut. Buddy took it home, planning to do some motor work…….nope, turned the chain around and to my knowledge it still cuts great.