New 540 owner

[Chuck M]

I recently bought the Minelab Vanquish 540 pro pack and it does take time to learn the machine but now I absolutely love it. If you are in a trashy site put the 8" coil on. I have already found 5 silver coins in about 6 weeks. This machine goes deep. I usually run the sensitivity 1 notch down.

 

Amazon Forum Fav 👍

Family Maps of Hinds County, Mississippi, Deluxe Edition - Grab it through Amazon!

[supertraq]

It's like learning a new language it takes time but it will become the norm given time..I have been using nothing but fishers and teknetics for 28 yrs so the minelabs is like greek to me but i'm learning it and it is proving it's self day by day.Hunt a demoed 1932 house again today and found 7 wheaties and a merc with the 8" coil,,missed all that with the 12" coil.Went back with my goldbug se 29er and found a wheaty and a silver rosie later today.

 

[Bruce R]

I recently bought the Minelab Vanquish 540 pro pack and it does take time to learn the machine but now I absolutely love it. If you are in a trashy site put the 8" coil on. I have already found 5 silver coins in about 6 weeks. This machine goes deep. I usually run the sensitivity 1 notch down.

How do you choose what to dig ? I get good high pitched hit in the 20-25 range and it turns out to be a zinc penny, it seems like there’s nothing worthwhile below 30 or so. I’ve read that nickels ring up at 9, but it sure seems like anything below 19 turns out to be junk. The other day I had a 20 hit so I switched it over to jewelry and it said it was a pull tab, I dug it up and sure enough, it was a pull tab. It seems like I have better luck with my old prism 2, I just don’t dig anything that rings up less than 25c.

 

[Xraywolf]

How do you choose what to dig ? I get good high pitched hit in the 20-25 range and it turns out to be a zinc penny, it seems like there’s nothing worthwhile below 30 or so. I’ve read that nickels ring up at 9, but it sure seems like anything below 19 turns out to be junk. The other day I had a 20 hit so I switched it over to jewelry and it said it was a pull tab, I dug it up and sure enough, it was a pull tab. It seems like I have better luck with my old prism 2, I just don’t dig anything that rings up less than 25c.

You have just made a decent case to hunt by sound and use VDI for bare reference, if that.
Alot of folks probably waste more time trying to figure out what it might be than if they just dug it up and found out for sure.

 

[Bruce R]

I was out with the 540 yesterday and noticed something aggravating, I’m searching in coin mode and I get a nice high pitched hit reading between 27 and 35, thinking I’ve finally found something nice, I dig it out and it’s iron. This was happening, say, 8 out of 10 times. Is it supposed to do that ? I thought it only hit on iron if that horseshoe was lit up ? Another thing I discovered today, a battery charger was supplied with the detector, but all it amounts to is a battery holder and a USB cord, no actual charger. I used the one for my iPad overnight and this morning the lights were solid green, I put the batteries in the detector and they’re stone dead. Any body else having these issues ?

 

[Tony-Ok]

Large iron will report as a good target. To check, use the horseshoe button. Coin size objects will be more accurately identified. Your pinpointed target should be small. Large iron is a problem for any detector. Most iron targets have a crackle or spitty sound coming off the target . Where as a coin will have a smooth audio. Trust the audio more than the ID. Hope that helps ..... HH Tony

 

[supertraq]

If your use to first texas or other solid beep and dig you will have to learn the minelab language as it is more of a blended raspy sound,but once you take time to learn it you will wonder why you waited so long as i did..

 

[supertraq]

Another thing is the 540 do not have modulated audio so you
'have to" raise the coil to see if its a big target or close to the surface,but it will soon become second nature to you and very useful....

 

[Rad1sh]

Also rotate 80 degrees on the target and see how it sounds and if the VDI stays consistent.