Chainsaw question: I'm missing something...?

Limitool

Limitool

Gold Member
Jun 9, 2013
5,925
8,310
Middle TN. area
Detector(s) used
White XLT Spectrum E-Series
Primary Interest:
Metal Detecting
I have a Stihl chainsaw w/18" bar. Fairly new and not used much. I've had a few hundred railroad ties stacked up for lining the driveway since last year. Well started to move them and had angles to cut at curves. After 2 cuts it was running hot and puked the chain. I changed out chain and made 3 cuts and again same thing. I took bar & chain off and cleaned up everything to make sure bar oil was in the oiler. I fired it up and yep.... oil pouring on out. Put a 3rd new chain on and cut 9 ties and same thing happened AGAIN...!

So is something wrong with the chainsaw or maybe it doesn't like cutting the railroad ties possibly. Why I wouldn't know but is it possible maybe? I am NOT hitting any metal nor seen any sparks at all. I stay a long ways from the metal end plates.

Any ideas anybody.... :dontknow:
 

Amazon Forum Fav đź‘Ť

DR.Ă–TEK Metal Detector, Waterproof Gold Detector, Pinpoint & Terrain Modes, Professional Metal Detector - Grab it through Amazon!
puked the chain? Chain popping off the bar? I found it helps to tighten the chain with the bar nuts loose. Once chain is tight, tighten the bar nuts last.
 

Good tips from bowwinkles.
I also think the creosote can make for difficult cutting. I know treated lumber puts more of a strain on my circular saw.
 

Quinc said:
puked the chain? Chain popping off the bar? I found it helps to tighten the chain with the bar nuts loose. Once chain is tight, tighten the bar nuts last.
Click to expand...
Chain not popping off bar. Chain just GOES DULL quickly. And I tighten exactly the way you mentioned about bar nuts. I always have.... last. Went through 2 brand new chains very quickly.
 

Limitool said:
Chain not popping off bar. Chain just GOES DULL quickly. And I tighten exactly the way you mentioned about bar nuts. I always have.... last. Went through 2 brand new chains very quickly.
Click to expand...
Ties have been buried, and from being coated with creosote it's a recipe for fine sand/dirt mixed in.

I'd power wash the cutting area before cutting.
 

pepperj said:
Ties have been buried, and from being coated with creosote it's a recipe for fine sand/dirt mixed in.

I'd power wash the cutting area before cutting.
Click to expand...
Well that ain't happening.... I have another saw that will cut them like butter but it's electric. I'll have to bust out the 100' 10 gauge homemade extention cord if I go that route... Nothing is ever easy...!

Or I'll have to wheel them out. Lay them up. Mark angle needed. Wheel back to shop. Cut and repeat. But I bet your right pepper....!!!! But these ties are NOT LIGHT at all. Balloon tires on 2-wheel cart helps BUT not going uphill and certainly NOT downhill either.

Thanks all....
 

Just a friendly word of warning…..not sure their age, but if treated with creosote make sure you have long pants, long sleeve shirt a gloves. That stuff (when put into sawdust) will hit you like a good sunburn.
 

ncsuwolf said:
Just a friendly word of warning…..not sure their age, but if treated with creosote make sure you have long pants, long sleeve shirt a gloves. That stuff (when put into sawdust) will hit you like a good sunburn.
Click to expand...
Thus far I've been alright. Well I think I am (stay tuned?). Think I'm moving to Plan B with the electric hand held Wellsaw. I still have a couple hundred feet of them to lay out yet. But most of that is mostly a straight line. Probably 15-20 to cut at angles yet though. Thanks for the advise.
 

You must log in or register to reply here.

google lens, Try it on this cave wall.

⬅️ Previous Thread

Top Member Reactions

Users who are viewing this thread

Total: 3 (members: 1, guests: 2)
High Plains Prospectors

Latest Discussions

Back
Top