Deus in Hot Ground

vferrari

Silver Member
Jul 19, 2015
4,910
8,377
Near Ground Zero for Insanity
Detector(s) used
XP Deus with HF/x35 Coils and Mi6 Pinpointer/ML Equinox 600/800/ML Tarsacci MDT 8000 GPX 4800/Garrett ATX/Fisher F75 DST/Tek G2+/Delta/Whites MXT/Nokta Simplex/Garrett Carrot
Primary Interest:
All Treasure Hunting
I am relic hunting near Culpeper and Orange Virginia for several days. In this hot soil the GPX, ATX, and TDI Pulse Induction machines are kings, but the Deus still makes the trip because it can still be used in the woods where the soil is not so hot and also because it is like a pinpointer on steroids around the huts, trash and fire pits! It cannot penetrate the soil too deep for natural subsurface finds (but will grab shallow targets like bullets that have plowed up to near the surface). But when it comes to scanning the dirt removed from a pit or the pit side walls, it is a huge time saver. Sifting the dirt is probably the best method but is time consuming, plus you have to lug the sifter into the field. Most folks try to use a pinpointer and that can just drive you insane especially with small pin nails and ration can pieces everywhere. Deus to the rescue to cherry pick the relics out of the dirt - better than a pinpointer, small enough to easily bring along into the field. It is not as foolproof as sifting as some targets still get masked by the trash and high mineralization, but its pretty close.

In the attached pic, used the Deus to snag the buttons and camp lead out of a fire pit, the bullets were GPX field finds. Had to keep that square nail, it was as pristine as the day it was forged (Deus found that masking some camp lead). Used a combination of gold field (all metal) and a fast program variant with full tones to pluck these out of the dirt piles and side walls. Several folks were using the Deus in similar fashion at some larger huts. Was hoping the MI-6 pinpointer would have this capability (tone and visual ID) as its form factor is more conducive to scanning side walls and piles inside the pit, but XP did not take it that far (yet). A huge missed opportunity in my opinion. In any event, the Deus got the job done itself and is the reason I have it strapped to my day pack when relic hunting even while primarily swinging a GPX in hot soil.

20170330_224742.jpg
 

Nice finds sounds like tough ground to work .glad your having success
 

Well done vferrari! Sadly I never fired up my Deus and only swung the GPX the whole time... however I did have it in the truck just in case I came across a pit. I would have done the exact same thing and switched over to the Deus in that situation. It was great meeting you and best of luck these next couple days. :occasion14:
 

Good going "H" :icon_thumleft: Always found it odd when a forged nail comes up clean.
 

Good going "H" :icon_thumleft: Always found it odd when a forged nail comes up clean.

I agree. I have no idea how that happens especially when its in the same hole as its rusty cousins.
 

Congrats! I hope to see more from you in the coming days.
 

What's is second row down, third to the right? I have one of the same. (Twice as thick as flat button, bent, and clipped or broken at bottom)
 

Last edited:
It's a partially crushed/bent eagle cuff. The other cuff is just the button back, the face exploded when I got it out of the hole. Heartbreaker.
 

BTW - I was redumacated on the square nail. Square nails before 1800's were mostly forged/wrought by hand. After that they were cut from sheets of steel until the modern wire nail came along later. So the proper way to say it was "the day it was cut". It may have been "annealed" in the camp fire and they may have changed its corrosion resistance or just the composition of the steel alloy had something to do with it plus the variability in the environmental conditions. Whatever the science, its cool to see one without corrosion.
 

Congratualtions on the nice finds! :occasion14:
 

Top Member Reactions

Users who are viewing this thread

Back
Top